Posted in

Why do jaw plates slip?

If you’re reading this, chances are you’ve spent a good chunk of change on jaw plates for your crusher — whether that’s a primary jaw crusher in a mining operation, a recycling plant processing concrete, or a quarry breaking down rock — and you’ve run into that frustrating, costly problem: they slip. As a jaw plates supplier with 12 years in the business, I’ve seen this issue derail production shifts, push maintenance budgets over the edge, and even lead to preventable safety incidents on worksites. I’ve also watched too many operators point fingers at the wrong culprit, skipping root-cause fixes and just replacing plates again and again, which only wastes time and money. Jaw Plates

Let’s break down why jaw plates slip, what’s actually going on under the surface, and how to stop it from happening to you. First, let’s get one thing straight: slipping isn’t a random defect or a flaw in the material — it’s almost always a preventable mix-up in installation, operation, or even plate design. I’ve encountered every scenario, from a miner who skipped torque checks on hold-down bolts to a recycler running too-small feed material through a crusher meant for heavy rock.

To start with the basics: jaw plates are the replaceable liners that line the two vertical jaws of a jaw crusher — one fixed to the main frame, the other to the pitman, which moves back and forth to crush material. The friction between these plates and the material inside the crushing chamber is what does the work; if that friction is compromised, the plates can slide instead of gripping, which means the crusher isn’t doing its job, you’re wasting energy, and you risk damaging other internal parts like the pitman or frame.

One of the most common causes I see is incorrect installation. It sounds simple, but so many operators cut corners here. Let’s talk about hold-down bolts. When you install new jaw plates, those bolts need to be torqued to the exact specification recommended by your crusher’s manufacturer — not “as tight as I can get with a wrench” or half of that. If bolts are too loose, the plate shifts when the crusher cycles, and the friction it’s supposed to create is lost. I once had a customer in Alberta call me at 2 a.m. because his jaw plates were slipping mid-shift; when our on-site technician arrived, he found the bolts were only torqued to 150 ft-lbs, when the spec needed 275 ft-lbs. That loose plate shifted just enough to break the side liner’s weld, and the whole assembly had to be replaced — not just the jaw plates.

On the flip side, over-torquing bolts is a lesser-known cause of slipping, too. If you crank those bolts too tight, you can warp the jaw plate or the mounting surface on the frame. Warped plates don’t sit flush, so there’s air gaps between the plate and the frame, which means the plate can’t grip the material properly when the crusher runs. I’ve seen a customer in British Columbia run into this: he used an impact wrench instead of a torque wrench, and warped three plates so badly they developed a concave curve. Within a week, all three were slipping, and he had to foot the bill for not just new plates but a resurfaced frame, too.

Another installation misstep? Skipping the shims. Jaw plates aren’t perfectly uniform — small gaps between the plate and the frame are normal, and if you don’t fill those with precision shims, the plate rocks back and forth during operation. That rocking loosens the plate over time, leading to slippage. I always tell customers to use high-density, heat-resistant shims — not cardboard or scrap metal — because those compress and can shift under constant vibration. I once watched a quarry save $12,000 in replacement costs just by taking the 10 minutes to add shims during a plate swap, instead of rushing to get the crusher back online.

Now, moving beyond installation: operator error is the second biggest cause of jaw plate slippage, and it’s something even seasoned crews miss. Let’s talk about feed size. Jaw crushers are designed for a specific maximum feed size — usually 80% of the crusher’s opening width, per industry standards. If you feed material that’s too big, the crusher can’t break it down properly, so the material gets stuck between the jaws instead of being crushed. That stuck material creates uneven force on the plates, making them slip. But wait, what if you feed material that’s too small? That’s a less obvious culprit, but I see it all the time. If you’re running tiny gravel through a crusher meant for 2-foot boulders, there’s not enough mass between the plates to create the friction needed to hold the material. The small pieces slide around, and the jaw plates follow suit — it’s like trying to grip a handful of marbles instead of a rock; your hand can’t get enough friction to hold on.

Then there’s the issue of closed-side setting (CSS). The CSS is the gap between the two jaws at the bottom of the chamber, which controls the size of the final product. If you set the CSS too tight, the crusher has to work harder to push crushed material out, creating extra force that can make the upper sections of the jaw plates slip. I had a recycling customer last year who kept replacing plates every 6 weeks; when we checked his CSS, it was set 10mm too tight. Loosening the CSS by just 5mm extended his plate life to 18 weeks, and eliminated all slippage. It sounds minor, but CSS is calibrated to every crusher, and even small deviations throw off the balance.

Material choice for jaw plates is another factor, and this is where suppliers often drop the ball. A lot of low-cost jaw plates on the market are made with generic steel that’s too soft or too brittle for the application. If your crusher is processing abrasive material like granite or reinforced concrete, you need plates made with high-manganese steel (Hadfield steel) — it hardens when struck, creating a rougher surface that grips material better. If you use a cheap, low-manganese plate, the surface wears down quickly, becoming smooth like a glazed ceramic. A glazed plate has almost no friction, so it slips almost immediately. I’ve seen a customer who bought budget plates online that wore down to a smooth surface in 3 days; switching to our high-manganese plates has cut his slippage issues to zero.

Wait, but even high-manganese plates can slip if they’re the wrong profile. Jaw plates come in different patterns — corrugated, tooth, smooth, and block — each designed for a specific application. For example, corrugated plates are great for primary crushing of large rock because their ridges create more grip. If you use corrugated plates in a secondary crusher processing small, fine material, those ridges can get filled with fines, smoothing the plate surface and leading to slippage. I always match plate profile to the feed material: corrugated for coarse, abrasive feed, smooth for fine, non-abrasive material. I once had a mine that used corrugated plates in their secondary crusher; switching to smooth plates stopped their slippage entirely and extended plate life by 40%.

There’s also the less talked about issue of jaw alignment. Over time, wear on the pitman bearings or frame can throw the fixed and moving jaws out of alignment. If one jaw is tilted even a few degrees, the force of crushing is uneven — one side of the plate takes more stress, causing it to shift. I had a construction company that was replacing plates every month because of slippage; when we checked their jaw alignment, it was off by 2 degrees. Realigning the jaws and replacing worn bearings fixed the slippage, and their plate life doubled.

Now, let’s talk about what happens when slippage isn’t fixed. It’s not just a hassle of replacing plates. Slippage can cause the plate to rub against other internal parts of the crusher, like the toggle plate or the pitman, leading to expensive component damage. It can also create inconsistent product size, which messes up downstream processes — like if you’re feeding a cone crusher, uneven size material can cause it to jam. Worst of all, loose plates can become dislodged during operation, which is a major safety hazard for crews nearby. I’ve seen a dislodged plate cause a crushed stone to a worker’s hand because the crew didn’t lock out the crusher before checking loose plates. That’s why addressing slippage early isn’t just about saving money — it’s about keeping worksites safe.

So, what can you do to prevent jaw plates from slipping? Let’s break down the actionable steps I recommend to every customer:

First, follow installation best practices: Always torque hold-down bolts to the manufacturer’s specified setting (use a torque wrench, not an impact wrench), add precision shims to fill gaps between plates and the frame, and make sure the plate sits flush with no warping. If you notice a warped plate after installation, swap it out immediately — even a small warp will cause slippage.

Second, calibrate your crusher settings correctly: Stick to the recommended maximum feed size (80% of the crusher’s opening width) and adjust your CSS to match the final product size you need. Avoid running material that’s too small for your crusher — if you have fine material, use a secondary crusher designed for that size.

Third, match your jaw plate to your application: Work with a supplier who can recommend the right material (high-manganese for abrasive material, alloy steel for impact), profile (corrugated for coarse feed, smooth for fine), and size. Avoid generic plates — they’re made for one-size-fits-all, which almost never works for your specific crusher and material.

Fourth, schedule regular inspections: Check your jaw plates for tightness every 50 hours of operation, or after any major shift change. Look for wear signs like glazed surfaces, warping, or loose bolts. Catching slippage early means you can fix it without replacing your entire plate assembly or damaging other parts.

I know how tempting it is to go for the cheapest jaw plates on the market, but that’s where a lot of customers go wrong. A $200 plate might seem like a steal, but if it slips and needs replacing every week, that’s $800 a month — not including the cost of downtime, repairs, and safety risks. A quality, properly matched plate from a reputable supplier might cost $500, but it lasts 3 months, has zero slippage, and keeps your crusher running smoothly. At the end of the day, it’s not about the initial cost — it’s about total cost of ownership.

If you’re dealing with jaw plate slippage, or you’re tired of replacing plates every few weeks, let’s talk. I’ve helped hundreds of operators across different industries diagnose and fix slippage issues, from installation mistakes to wrong plate choices. We’ll review your current setup, recommend the right plates for your application, and walk you through the installation and maintenance steps to keep slippage from derailing your operations.

Screening Parts References

  1. Kostrzewa, P., & Gawlik, J. (2019). Analysis of Jaw Crusher Liner Wear and Slippage Phenomena. Mining Science, 26, 127-142.
  2. Society for Mining, Metallurgy & Exploration. (2021). Guide to Jaw Crusher Operation and Maintenance. SME Handbook for Aggregates and Mining.
  3. Zhang, Y., et al. (2020). Effect of Jaw Plate Profile on Friction and Crushing Efficiency in Primary Jaw Crushers. International Journal of Rock Mechanics and Mining Sciences, 132, 104357.
  4. ASTM International. (2018). Standard Specification for High-Manganese Steel Castings for Crusher Liners. ASTM A128-18.

Quzhou Horbon Mining Parts Co., Ltd.
Quzhou Horbon Mining Parts Co., Ltd. is one of the most professional jaw plates manufacturers and suppliers in China, featured by high quality customized service and OEM service. Please rest assured to buy premium jaw plates at competitive price from our factory. Contact us for pricelist.
Address: No.8 Nanshan Road, Qujiang District, Quzhou City, Zhejiang Province, China
E-mail: horbonmining@gmail.com
WebSite: https://www.horbonmachinery.com/